Wiring Diagram for FREEVISION® Antenna to Television
FREEVISION® Antenna
(Side View—mount not included with all models)
Back of TV
Note: the matching transformer
must be connected as described
on page 4 of the manual.
Antenna/Cable In
Coax Connection Port
Coax Cable
Winegard model AP-8700 preamplifier and model PS-1403 power inserter are shown above.
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000 • 800-288-8094 • fax 800-247-8221 • www.winegard.com • Printed in U.S.A. ©2011 Winegard Company • WC-1051
Wiring Diagram for FREEVISION® Antenna with Existing Indoor Coax Connection
Coax Connection on TV
FREEVISION®
Antenna
Antenna/Cable In
Coax Connection Port
Cable
Existing Coax
Connection*
a
Co
*The existing coax connection may be a 2-, 3-, 4- or 6- port splitter. A 2-port splitter is shown here.
Depending on the amount of signal received, a distribution amplifier may be required to power the system. Winegard recommends model HDA-100 distribution amplifier.
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000 • 800-288-8094 • fax 800-247-8221 • www.winegard.com • Printed in U.S.A. ©2011 Winegard Company • WC-1051
Wiring Diagram for FREEVISION® Antenna with Grounding Block and Existing Coax Connection
Coax Connection on TV
FREEVISION®
Antenna/Cable In
Coax Connection Port
Antenna
Point toward
stations.
Note: ground wire
(#8 or larger)
must run from
grounding block
to ground rod
e
Grounding
Block
Coax
(not shown here).
*The existing coax connection may be a 2-, 3-, 4- or 6- port splitter. A 2-port splitter is shown here.
Depending on the amount of signal received, a distribution amplifier or preamplifier may be required to power the system. Winegard recommends model HDA-100 distribution amplifier or AP-8700 preamplifier.
Refer to the National Electronic Code for antenna grounding specifications.
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000 • 800-288-8094 • fax 800-247-8221 • www.winegard.com • Printed in U.S.A. ©2011 Winegard Company • WC-1051
Wiring Diagram for FREEVISION® Antenna with Preamplifier, Grounding Block & Existing Coax Connection
Preamplifier Connections
Coax Connection on TV
Underside of Preamplifier
FREEVISION®
Antenna
Antenna Input
Antenna/Cable In
Coax Port
Power Supply Input
Point toward
stations.
Preamplifier
Note: ground wire
(#8 or larger)
must run from
grounding block
to ground rod
e
Grounding
Power
Inserter
Block
Coax
(not shown here).
Existing Coax
Connection*
*The existing coax connection must be a splitter that is AC/DC passive on one leg only. The power supply must be connected to the AC/DC passive leg of the existing coax connection.
Refer to the National Electronic Code for antenna grounding specifications.
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000 • 800-288-8094 • fax 800-247-8221 • www.winegard.com • Printed in U.S.A. ©2011 Winegard Company • WC-1051
|
Well Traveled Living Patio Heater 60405 User Manual
West Bend Can Opener 77201 User Manual
Western Digital Computer Drive WD10EADS User Manual
Whistler Radar Detector 1605 User Manual
Winegard Satellite TV System WI DM04 User Manual
Wolf Appliance Company Cooktop SRT484CG User Manual
Wyse Technology Personal Computer 883886 01 User Manual
Yamaha DJ Equipment EMX5014C User Manual
Yamaha Guitar 11391 User Manual
Zebra Technologies Printer DA402 User Manual